In connector and lead frame design, strength and conductivity have always fought each other. C19700 (CuFe1MgP / K85) is the precipitation-hardened copper-iron-magnesium-phosphorus alloy that resolves this trade-off-not by compromising one property for the other, but by delivering 80% IACS electrical conductivity alongside tensile strength in the 415–550 MPa range, depending on temper.
Its defining advantage is visible when set against the industry workhorse C19400: C19700 delivers roughly 25% higher conductivity (~80% IACS vs. ~60–68% IACS) while maintaining comparable strength and formability. For high-density connectors, thinner lead frames, and fuse clips, that conductivity headroom translates directly into less resistive heating and more current-carrying capacity in the same package footprint.
HS Metal supplies C19700 in strip, wire, rod, and custom blank forms, with tempers from annealed through H08, and Mill Test Certificates for every export lot.
Technical Specifications
| Property | Value | Remarks |
|---|---|---|
| UNS / Common Names | C19700 / CuFe1MgP / K85 | ASTM B465 / B888 |
| Composition (wt.%) | Cu balance; Fe 0.30–1.2; Mg 0.01–0.20; P 0.10–0.40 | Sn, Zn, Pb ≤0.20/0.03 max |
| Electrical Conductivity | 80% IACS (46 MS/m) | Defining property |
| Thermal Conductivity | 320 W/(m·K) | |
| Density | 8.84–8.92 g/cm³ | |
| Modulus of Elasticity | 120–121 GPa | |
| CTE (0–300°C) | 17.3 × 10⁻⁶/K | |
| Melting Range | 1040–1090°C | |
| Annealed (O) | UTS 295–365 MPa; YS ≥110 MPa; Elongation ≥20% | |
| H02 (Half-Hard) | UTS 365–435 MPa; YS ≥250 MPa; Elongation ≥6% | |
| H04 (Hard) | UTS 415–485 MPa; YS ≥365 MPa; Elongation ≥2% | |
| H06 (Extra-Hard) | UTS 460–505 MPa; YS ≥440 MPa; Elongation ≥2% | |
| H08 (Spring) | UTS 485–525 MPa; YS ≥460 MPa; Elongation ≥2% | |
| Forms | Strip/Foil (0.05–5.0 mm, width up to 300 mm); Wire; Rod; Custom blanks | Custom slitting available |
👉 Explore C19700 Specifications & Request a Sample
C19700 vs. C19400: The Selection Boundary
| Property | C19700 (CuFe1MgP) | C19400 (CuFeP) |
|---|---|---|
| Electrical Conductivity | ~80% IACS | ~58–68% IACS |
| Tensile Strength (H02) | ~365–435 MPa | 310–380 MPa (typical) |
| Yield Strength (H02) | ≥250 MPa | Lower than C19700 |
| Thermal Conductivity | ~320 W/(m·K) | ~260 W/(m·K) |
| Softening Resistance | Excellent | Good |
| Cost Position | Moderate premium over C19400 | Lower |
| Choose When | Conductivity is the limiting factor-excess heating or current capacity in a fixed cross-section | Strength requirement is slightly higher and 60–68% IACS satisfies the thermal budget; high-volume legacy lead frame programs |
The decision rule: If your connector or lead frame is running too hot, or you need more current in the same package size, C19700 is the upgrade. If your thermal design already passes with C19400 and you need every fraction of strength at the lowest material cost, C19400 remains the established choice.
Available Forms
We supply UNS C19700 in all standard and custom forms:
| Form | Specifications | Typical Applications |
|---|---|---|
| Wire | Various diameters – coils or spools | Connector pins, spring contacts, lead frame bonding wire |
| Strip / Foil | Thickness: 0.05–5.0mm; Width: up to 300mm | Stamped connectors, lead frames, electrical contacts |
| Sheet / Plate | Custom dimensions | Busbars, heat sinks, machined components |
| Custom Shapes | Per engineering drawings | Special connectors, switch components |
Available tempers: Annealed (O), H02 (half‑hard), H04 (hard), H06 (extra hard), H08 (spring).
👉 Send your specification for a quotation
Why C19700: The Engineering Case
1. Higher Conductivity Without Sacrificing Strength
C19400 achieves strength through higher iron content (2.1–2.6% Fe). C19700 uses a leaner iron level (0.30–1.2% Fe) combined with magnesium (0.01–0.20% Mg) and phosphorus for precipitation hardening. The result is comparable H02 tensile strength (~400 MPa for C19700 vs. 310–380 MPa for C19400) at a conductivity level that C19400 cannot reach.
2. The Thermal Advantage in Practice
At the same current, C19700 generates approximately 20% less resistive heat than C19400. For high-density connectors and power lead frames, this thermal margin can be the difference between passing and failing a derating specification.
3. Stress-Relaxation Resistance for Spring Contacts
C19700 maintains stable spring contact force under sustained temperature fluctuation, resisting the contact-resistance rise that leads to connection failure in spring-loaded terminals.
4. A Drop-In Upgrade from Bronze, Brass, and Beryllium Copper
Phosphor bronze (C51900) offers ~15% IACS. Brass sits at 20–30% IACS. C19700 at 80% IACS reduces resistive heating by more than half compared with brass, without the cost premium of beryllium copper in applications that do not require BeCu's ultimate strength.



Why Source Custom C197 Copper Alloy From HSMetal
1. Full ASTM B465 / B888 compliance. Mill Test Certificate with every shipment.
2. Custom slitting to your width. Strip from 5 mm to 600 mm, slit to your exact specification.
3. Multiple tempers in stock. Annealed through H08, matching your forming and strength requirements.
4. Fast delivery from stock. Standard sizes ship in 7–15 days; custom-cut confirmed at order review.
5. Technical support for alloy selection. Not sure whether C19700 or C19400 is right for your connector design? Send us your current, temperature rise, and formability requirements - we will recommend the right alloy and temper.
If you need high‑strength, high‑conductivity custom C197 copper alloy wire, strip or rod, please send us your drawings, dimension requirements and target specifications to get a competitive quotation.
👉 Send Us Requirements & Request Quotation
Key Applications
| Industry | Specific Applications |
|---|---|
| Electrical & Electronics | High‑performance connectors, relay contacts, switch components, plug blades |
| Semiconductor | Lead frames, IC packaging components |
| Automotive | EV battery connectors, terminal blocks, sensor housings |
| Telecommunications | High‑frequency connector pins, RF components |
| Industrial | Electrical springs, thermostat components, circuit breaker parts |
Commercial and Delivery Term
| Item | Details |
|---|---|
| MOQ | 50 KG; small trial orders negotiable |
| Lead Time | 10‑18 working days for standard sizes; 18‑28 working days for fully custom temper or dimensions |
| Payment Terms | T/T 30% deposit, 70% before shipment; L/C at sight for large orders |
| Price Terms | FOB, CFR, CIF. Main ports: Shanghai, Ningbo, Qingdao; shipment available to Jebel Ali, Mombasa, Bangkok, Los Angeles and major European ports |
| Packaging | Export seaworthy package: scratch‑resistant protective film + wooden pallet / wooden case |
| Shipping | Sea freight, air freight; international courier for small test samples |
| Sample Service | Free small C19700 CuFe1MgP K85 samples; buyer undertakes courier freight cost |
| Shipping Documents | Commercial invoice, packing list, MTC, certificate of origin |
About Us
HSMetal is a professional Chinese manufacturer focused on high‑strength, high‑conductivity copper‑iron alloys. We specialize in UNS C19700 and C19400 copper alloy wires, strips and rods, serving global electrical, automotive and electronics industries with standard and customized metal solutions.
We stand out from ordinary suppliers with professional pre‑production technical auditing. Strictly following ASTM B99 and ASTM B465 standards, our engineering team checks and corrects incorrect or non‑standard parameters to prevent production defects and material losses for every client.
We have rich global export experience. We once completed a combined shipment of C197 and C194 copper alloy wires for a Pakistan electronics manufacturer. By revising the client's wrong C194 technical parameters and producing in full compliance with international standards, we achieved qualified and on‑time delivery with complete MTC documents.
We implement strict full‑process quality control. Each batch of C197 copper alloy is tested for chemical composition, conductivity, mechanical properties and dimensional tolerance. We support sample orders and mass customization, providing complete export documents and stable logistics for Pakistan, Southeast Asia and worldwide markets.
Dedicated to reliable alloy supply, HSMetal offers one‑stop customized solutions for C197 high‑strength high‑conductivity copper alloy.
Our Factory

Closing Machine Of The Rolling

Aging Treatment Equipment

Horizontal Wire Drawing Machine

Rotating+Passing Eddy Current Flaw Detector

Electron Microscope

German Spike Spectral Analyzer
Resolve the Conductivity Trade-Off
If your connector, lead frame, or fuse clip is limited by resistive heating-or if C19400's 60% IACS is forcing an oversized cross-section-C19700 is the engineered answer.
Send us your current rating, allowable temperature rise, temper, and dimensional requirements, and our team will confirm whether C19700 or C19400 is the right alloy for your design before quotation.
FAQ
Q1: What is C19700 copper alloy used for?
A: C19700 is used for electrical and electronic connectors, lead frames, fuse clips, circuit breaker components, cable shielding, and spring contacts . It is chosen when you need higher electrical conductivity than C19400 without sacrificing strength and formability .
Q2: What is the difference between C197 and C194?
A: Both are copper‑iron alloys under ASTM B465, but C197 offers ~80% IACS conductivity vs. C194's ~60% IACS. C197 also provides superior softening resistance and similar strength to C194. C197 is the preferred choice when higher conductivity is required without sacrificing strength.
Q3: What is the electrical conductivity of C19700?
A: C19700 delivers 80% IACS (46 MS/m) electrical conductivity . This is significantly higher than brass (C36000: ~26% IACS), phosphor bronze (C51900: ~15% IACS), and C19400 (58–68% IACS).
Q4: What are the typical applications of C197?
A: High‑performance electrical connectors, relay contacts, lead frames, switch components, connector pins, electrical springs, and automotive terminals.
Q5: Can C19700 replace beryllium copper?
A: For conductivity-critical applications, yes. C19700 offers 80% IACS conductivity compared to beryllium copper (C17200: 17–28% IACS) - nearly 3–4× higher . However, beryllium copper offers higher strength and better stress relaxation resistance. Choose C19700 when conductivity is the priority; choose beryllium copper when maximum strength is required.
Q6: What tempers are available for C19700?
A: Available tempers include Annealed, H02 (1/4 hard), H04 (1/2 hard), H06 (3/4 hard), and H08 (full hard) . Temper selection depends on required strength and formability. For connectors requiring forming after stamping, H02–H04 is common. For lead frames requiring maximum strength, H06–H08.
Q7: What standards cover C19700?
A: C19700 is covered by ASTM B465 (Copper-Iron Alloy Plate, Sheet, Strip, and Rolled Bar) and ASTM B888 (Copper Alloy Strip for Electronic Applications) .
Q8: Can C19700 be soldered and brazed?
A: Yes. C19700 has excellent soldering and brazing characteristics . It also has excellent capacity for both cold and hot forming .
Q9: What is the one-line rule for choosing C19700?
A: Choose C19700 copper alloy when you need 80% IACS conductivity combined with 500–550 MPa tensile strength for connectors, lead frames, and electrical components - especially when C19400's conductivity is insufficient for your thermal or current-carrying requirements. For slightly higher strength and a lower conductivity requirement, C19400 remains a proven choice.
Q10:What is C19700 copper alloy? What does CuFe1MgP / K85 mean?
A: C19700 is precipitation hardening high‑strength copper alloy. CuFe1MgP is its chemical designation and K85 is its common industry alias. It delivers balanced high strength and high conductivity, widely used for semiconductor lead frames, connectors and electrical spring components.
Q11: Can you produce custom temper and custom sizes for C19700 (CuFe1MgP / K85)?
A: Yes. We supply C19700 copper alloy strip, sheet and plate with custom thickness, width, flatness and temper according to technical drawings. Cut‑to‑size blank service is available.
Q12: Is C19700 (K85) RoHS compliant for electronic export?
A: Yes. C19700 CuFe1MgP / K85 meets RoHS requirements. MTC and compliance documents can be provided for customs clearance and third‑party inspection.
Q13: Can I get C19700 CuFe1MgP K85 samples for performance testing?
A: Free small‑size C19700 samples are available. Customer covers courier freight, sample preparation takes approximately 3‑5 working days.
Hot Tags: C19700 high-strength copper alloy, CuFe1MgP, K85 copper alloy, C19700 vs C19400, high conductivity copper alloy, lead frame copper alloy, connector copper alloy, C19700 strip and wire

